Steeda Autosports, the world's largest aftermarket manufacturer of Ford performance equipment is once again leading the performance market with our High-Velocity Steeda ProFlow Mustang Cold Air Intake for 2015-2019 Ford EcoBoost Mustang and flash custom tuning device package.
This intake/tuning package called our Steeda ProFlow EcoBoost Mustang Ultimate Induction Power Pack combines our High-Velocity Cold Air Intake for your Ford Mustang EcoBoost with a SCT BDX tuning device for the ultimate easy to install power upgrade.
This Steeda ProFlow Mustang Cold Air Intake for 2015-2019 EcoBoost Mustang opens up the intake system of Ford's new turbocharged 2.3L power plant and allows it to breathe much more freely than the stock intake system allows - taking your 2015-2019 EcoBoost Mustang to the next level of performance.
Our engineers started with a large surface area high-flow nano-fiber air filter, added our famous 'race-tested' velocity stack entry and then designed a black rotary-molded heat shield with a durable rubber gasket to seal the shield against the vehicle's hood.
You would think this is more than enough, but we went the extra mile and designed this intake system to with a complete replacement intake tube from the CAI box to the turbo!
This Steeda ProFlow Mustang Cold Air Intake for 2015-2019 EcoBoost Mustang is so effective at improving airflow to the engine that simply bolting it on will increase your horsepower and torque. Combined with a custom tune using an SCT BDX Flash programming device we have achieved dramatic power and torque increases!
You have the option to run this bolt-on CAI with or without a tune. Please reference our dyno sheet included in the images above:
- Baseline run (non-PP): 256.51 rwhp and 288.27 ft/lbs tq
- CAI installed (factory tune): 283.21 rwhp and 298.03 ft/lbs tq
- CAI installed with Steeda tune: 304.28 rwhp and 366.26 ft/lbs tq
With no tune, we saw a gain of 26.7 rwhp and 9.76 ft/lbs tq!
With a Steeda tune, we saw a gain of 47.77 rwhp and 77.99 ft/lbs tq over stock!
Purchase the Steeda ProFlow EcoBoost Ultimate Induction Power Pack for your 2015-2019 Mustang EcoBoost from Steeda Autosports today!
Warning: Not approved for sale in California or states that require a California E.O. #. This part has been designed and is intended for off-road application only. Installation of this part on a vehicle that is driven on public roads may violate U.S. and Canadian laws and regulations. Steeda Tuning will not change, remove or alter any emissions control devices on your vehicle.
NOTE: Federal and several state and provincial laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. Steeda Autosports assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer's modifications and/or use of Steeda products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
- New tuning devices are shipped out "blank". Upon receiving the device, utilize it to retrieve your vehicle's Strategy Code
- With the strategy code, visit our Custom Tune Request Form. Fill out the requested details on your car.
- Your Custom Steeda Tune will be emailed to you in approximately 7 days. Download the tune onto the device, flash your vehicle and enjoy the new performance.
- Dramatically increase horsepower and torque
- Best designed/engineered intake on the market
- Retains factory cold air inlet ducting
- Easy installation
- Steeda tune with Steeda EcoBoost CAI - 47.77 rwhp and 77.99 ft/lbs tq
- Limited lifetime warranty
WARNING: California Residents: Cancer and Reproductive Harm;
www.p65warnings.ca.gov
- Installation Difficulty:
- Easy
- Tools Required:
- Basic Shop Tools
- Estimated Install Time:
- (approx.) 1 Hour
- Vehicle Fitment:
- 2015, 2016, 2017, 2018, 2019
- Vehicle Trim:
- EcoBoost
